|
This is a USA Version All boxes and paper will be included. * 894.00001 - 1999.99999* MHz (*guaranteed: 0.1 - 1000 and 1240 - 1300 MHz) * Mode: SSB (USB,LSB); AM (Normal, Wide, Narrow); WFM; FM (Normal, Narrow); CW (Normal, Narrow*) (*optional filter required) * Number of memory channels: 1000 (plus 20 scan edges and 1 priority channel) * Below 30 MHz: SO-239 (50 ohms/Phono [RCA (500 ohms)]) * Above 30 MHz: Type-N (50 ohms) * Usable Temperature Range: -10°C ~ +50°C; +14°F ~ +122°F * Frequency stability (in FM mode): * Below 30 MHz: ±100 Hz (optional ±20 Hz) * Above 30 MHz: ±3 ppm (optional ±0.6 ppm) * Tuning steps: 10, 50, 100 Hz; 1, 2.5, 5, 9, 10, 12.5, 20, 25, 100 kHz; 1 MHz or programmable (0.5 - 199.5 kHz/0.5 kHz steps) * Power Supply Requirement: 13.8 V DC ±15% (negative ground) or 117/220/240 VAC (with AD-55/A/V) * Current drain (at 13.8 V DC): * Dimensions: 287(W) x 112(H) x 309(D) mm; 11.3(W) x 4.4(H) x 12.2(D) in * Receive system: Superheterodyne * 1st: 48.8 MHz (0.1-29.99999 MHz); 778.7 MHz (30.0-499.99999 MHz); 266.7 MHz (500.0-1024.99999 MHz) * 2nd: 10.7 MHz (0.1-29.99999 MHz); 10.7 MHz (30.0-499.99999 MHz); 10.7 MHz (500.0-1024.99999 MHz) * 3rd*: 455 kHz (0.1-29.99999 MHz); 455 kHz (30.0-499.99999 MHz); 455 kHz (500.0-1024.99999 MHz) (*except WFM) * Squelch sensitivity (threshold/tight): * SSB, CW, AM-N: 10 µV/320 mV * FM, AM, AM-W: 0.4 µV/320 mV * WFM, SSB, CW, AM-N: 4.5 µV/320 mV * WFM: More than 150 kHz/-6 dB * FM, AM-W: More than 12 kHz/-6 dB * AM, FM-N: More than 5.5 kHz/-6 dB * AM-N, SSB, CW: More than 2.2 kHz/-6 dB * Spurious and image rejection ratio: * 1.8-29.99999 MHz: More than 60 dB * 30-1000/1240-1300 MHz: 50 dB (typical) * Audio Output Power (at 13.8 V DC): More than 2.0 W at 10% distortion with an 8 ohms load. * IF shift variable range: More than ±1.2 kHz * External speaker connector: 2-conductor 3.5 mm (1/8 in)/4-8 ohms Options Included Amd installed in radio are listed below. * FL-52A CW NARROW FILTER: Center freq: 455 kHz; Bandwidth: 500 Hz/-6 dB * UT-102 VOICE SYNTHESIZER UNIT: Provides audible confirmation of an accessed band's frequency. The Icom SP-23 It is 8 ohms and is rated at 2 watts [4 watts maximum]. The SP-23 with four separate audio network filters [HPF1 500 Hz, HPF2 250 Hz, LPF1 3000 Hz, LPF2 1000 Hz]. Input A or B may be selected so two radios may share this speaker. There is a speaker on-off switch and a 1/4 headphone jack on the front panel. Metal construction 5.75 x 4.25 x 11.2 inches 3.6 lbs. (145x111x283mm 1.65 kg). The bottom panel of the speaker features a pull-out tilt stand if you wish to angle the speaker. A single audio cable is supplied with a mono mini plug at both ends. The cd-2 needs to be connected to a power source such as a power supply . NO POWER SUPPLY INCLUDED. The CD-2 quickly and accurately decodes and displays any of the following conventional codes: CTCSS/DCS displays are temporarily interrupted to display DTMF upon occurrence. All DTMF displays are stored and replayed slowly permitting observation of fast ANI or speed-dialer codes. The CD-2 is also used to remotely display user programmed data from our TP-154, TP-154 PLUS and TP-163 Repeater Tone Panels. The CD-2 also has an RS-232 serial port which makes all decoded data available to your personal computer using CD-2P Software for your PC. The optional CD-2P PC compatible software allows your PC to store hits, time and date of all received CTCSS, DCS and DTMF codes. Graphical displays show channel loading etc. Convenient menus allow you to view or print any of the following which has accumulated in your computer: * Download and printout all programming data from your TP-154, TP-154 PLUS and TP-163 tone panels CD-2 Installation Decoding DCS requires a direct connection to the FM detector of your receiver (De-mod output of your service monitor). If you only wish to decode CTCSS and DTMF a connection to the speaker leads will function with most scanners. An internal pre-amp with level control allows input levels from 10 mV to 4 volts. Internal jumpers allow set-up options such as selecting DCS polarity. THE CD-2 DECODES EACH OF THE FOLLOWING CODES: MECHANICAL (CD-2, LT-2, CD-2-CAR) Height: 1.8 in. ***** May also have icom software would have to search my home for this item ***** (please look at our rules and privacy policy) |
deborah-england@machine--tools.com (Deborah England) for additional information. This email is used for forwarding to newsgroup user.