|
ICOM IC-91A V/U Dual Band Handhled Radio Warranty: 1 Product code: ICOM IC-91A * IC-91A TX:137-174, 400-470MHz, RX:0.495-999.99 MHz(unblocked) V/U IPX4 Water-Resistant Transceiver Handheld Radio body * ICOM BP-217 Li-lon 7.4V/1300mHz Battery pack * ICOM BC-167A 120V AC adapter (we can offer converter 220-240V AC adapter, only extra USD$ 10 for it) One radio. Two bands. Three times the fun! Wide band receiver with dualwatch capability The IC-91AD/A has dualwatch receiver capability,allowing you to receive* two bands simultaneously (including same band). By pushing and holding the [Main/Dual] button, you can easily turn dualwatch on and off, while a press of the button allows you to toggle the active VFO channels. *See specifications for receive range coverage. Using a large full dot-matrix LCD (37.8×20mm; 11/2×25/32 in), the IC-91AD/A clearly shows two-line frequency settings, alphanumericchannel name, bandscope, etc. You can hoose large or small font size in the setting mode. In addition, automatic LCD and keypadbacklighting provides bright illumination for night time operation. Spectrum activity is displayed on the screen and audio is heard while sweeping the range. It is useful for finding new or interfering signals. Icom’s original wideband PA circuit and supplied lithium-ion battery pack provides 5W (typ.) output. The supplied BP-217 provides up to 5/4.5 hours* of operating time and greatly reduces both the size and weight needed to obtain full output power. * VHF/UHF single mode, Tx high: Rx: Stand-by duty ratio= 1: 1: 8 The 4 cursor direction buttons on the keypad gives you quick and intuitive access to many settings. The twin volume/channel knob provides convenient channel/volume setting. An external DC power jack allows for operation with an external DC power supply (10–16V DC). When used with the CP-19R or OPC-254L, simultaneous operation during charging is possible. Built-in CTCSS/DTCS encoder and decoder CTCSS and DTCS tones are used for accessing a repeater or for tone squelch operation. The pocket beep alerts you with a beep sound when the transceiver receives a preset tone. * Squelch release function to monitor a weak signal. * Water-resistant construction, equivalent to IPX4 * Auto power save, power off and power on * 26 memory banks with selected bank and bank link scanning * 10 channel DTMF memory (16-digit) * 10dB (approx) built-in attenuator * Total of 1304 memory channels Advanced digital technology in your hand now! D-STAR DV mode available (Digital Voice + data) The IC-91AD* provides DV mode operation with an AMBE codec. 950 bps data can be sent simultaneously with the digital voice transmission. When you receive an FM mode (or other mode) signal while operating in DV mode, the automatic DV detection function changes the operating mode to the one detected. * Optional UT-121 is required for use with IC-91A. The newly adopted one-touch reply [CALL RX->CS] button memorizes the received callsign(s) at the touch of the button. This function allows you to respond to the calling station without hassle. In addition, up to 20 received callsigns are stored in a received call history. Built-in voice recorder and auto reply function The built-in voice recorder* records an incoming call for up to 30-seconds (approx.), (or 15 sec. × 2 tracks, 10 sec. × 3 tracks). The 10 sec. transmit memory allows you to record your callsign, CQ and automatically answers when you receive a message. Optional PC remote control capability When connected to a PC via an RS-232C cable, most functions of the IC-91AD/A* can be controlled from the PC with the optional RS-91 software. In DV mode operation, you can send and receive short messages of 20 characters (Max.) on the PC. (* Also available in analog mode) When connected to an external GPS receiver (NMEA 0183 format), your own and other station’s position information can be sent and received*. The IC-91AD sends the position data either by holding the PTT switch, or at a preset interval (5 sec.–30 min.), depending on the setting. * GPS data receive only when no external GPS receiver is attached. DX communication over the D-STAR system The D-STAR repeaters for 144, 440MHz are now available. It allows cross band (144/440/1200MHz) operation and long distance communication over the D-STAR system. Transmit Freq. Range: 137 - 174 MHz 400-470 MHz Receive Freq. Range: < A band > 0.495-999.99 [cellular unblocked] 118.000 - 174.000MHz 350.000 - 470.000MHz Mode: FM/AM/DV(require UT-121 for the IC-91A) Op. Temperature Range: -20° C - +60° C Frequency Stability: ±2.5 ppm (-20° C - +60° C) 25° C is standard Digital Trans. Speed: 4.8 kbps Antenna Impedance: 50 ohms unbalanced (SMA type) Memory Channels: 1304 channels (includes memory, call and scan-edge) Power Supply Voltage: DC 7.4V (BP-217) External terminal: DC 10.0 - 16.0 V Battery terminal: DC 5.0 - 10.0 V Frequency Resolution: 5, 6.25 and 8.33 (in air band), 9 (AM radio band), 10, 12.5, 15, 20, 25, 30, 50, 100, 125 and 200 kHz External Size: 58.4 (W) x 103 (H) x 34.2 (D) mm Xmit Power Consumption: Hi: 5W/ 2.1 A (typ), Lo: 0.5W/0.8 A (typ) Modulation Type: FM/FM Phase Reactance, DV/GMSK Phase Reactance Freq. Deviation: FM Wide/±5.0 kHz, Narrow/±2.5 kHz 2.Bank wire transfer (requires an extra US$10 service charge) Increase your sales with MerchantRun's Cross-Border Trade Solution (please look at our rules and privacy policy) |
e_tate@machine--tools.com (Esperanza Tate) for additional information. This email is used for forwarding to newsgroup user.
